Your computers motherboard is a critical component that plays a major part in what other components you can and cant install. Motherboards have a reputation for being finicky to troubleshoot, however, which keeps some PC enthusiasts fearful of ever touching it, let alone attempting to replace one. On rare occasions, you might even have motherboard issues with a new PC these include random reboots, refusing to boot up, and continual crashes citing fatal exceptions, illegal operations, and general protection fault error messages.
Fortunately, some of the most common problems you can run into with your motherboard are relatively easy to fix. All you need is a little patience.
Not enough power
Yes, listing check the power as the first step in any guide is a bit cliché, but its an absolute must here as motherboards have not just one power connection but two. Theres a main 20-to-24-pin connector and a second four- or eight-pin connector hidden away by the processor socket. Many people forget the second connector weve done it before in our early PC building days, so you should check to make sure that both are plugged in correctly. Unplug and plug them back in if youre unsure how well fitted they are.
Make sure both plugs are fully seated and properly matched with the correct power supply cords. This will solve many issues, particularly those that crop up when installing a new motherboard for the first time. You should also consider running hardware and utility diagnostics if it is possible to do so on your PC, such as the Intel Processor Diagnostic Tool, CPU-Z, and PassMark Performance Test.
Improperly installed components
Components can cause a motherboard to malfunction if theyre not properly installed. In some cases, your computer may not even get through POST [a self-testing mechanism employed by PCs during boot-up] or even turn on. Potential culprits include the processor, video card, and RAM.
Improper seating of the video card and RAM are the most likely sources of your problems, because issues in those areas are easy to overlook. Examine the video card, and make sure that its evenly seated across the width of the PCI-Express slot. Then, give it a firm downward push, just to be sure.
The RAM slot has two plastic wings that should snap over the sides of each stick of memory. These should be standing upright 90 degrees from the motherboards surface and securely inserted around the tabs found on each side of your RAM sticks. If one or both wings are slightly askew, the RAM isnt properly installed.
Properly installing a processor is much more difficult but worth checking if youre really stumped. The pins and the slot on the processor and motherboard must be properly lined up. Once inserted, the processor should sit flat on the sockets surface. The processors heatsink should also attach firmly.
For more help on installing or reinstalling a processor, check out our guides to installing Intel and AMD CPUs.
A short circuit
Motherboards are filled with capacitors and soldered connections that route data and power from one part of the board to another. As you may have noticed, the motherboard is held aloft from the PC case by a series of screw-in standoffs that are about a quarter-inch thick. These exist because the motherboard can short if it makes contact with other metallic components causing the capacitors to blow out, bulge, and even leak fluid which makes performing a physical inspection of components crucial to diagnosing issues. However, unless you are extremely confident with your skills with a soldering gun, replacing your capacitors is best left to professionals.
A motherboard experiencing a short may not get through POST, may complete POST but then behave erratically, or may boot but then crash at random. A failure to pass the POST process is the most frequent symptom, but other situations can occur even if only occasional contact is made between the motherboard and the case.
Examine how your motherboard is installed. Check that you used the standoffs that keep the motherboard from contacting the case and ensure that any unsupported portions of the motherboard havent bent toward the cases interior. Also, check that all internal wires are properly shielded with a rubber or plastic exterior.
No case power button connection
The power button on a computers case connects to the motherboard through a small, thin two-pin wire. Without this important but easy-to-miss connection, your computer wont start. Thats because the motherboard never receives the command to do so if you press the power button when the wire isnt connected to the proper pins on your motherboard. Hard to believe that a bent or misaligned pin could cause you so much grief, but with a steady hand and steely resolve, this issue can be remedied. Note that attempting to straighten pins can easily cause them to break and require you to replace components like your CPU, so think long and hard before trying it yourself.
Connecting the power button can be difficult. Unlike so many other motherboard connectors, which are designed to make improper installation impossible, the power button connector usually is labeled only with small symbols like Pwr+ and Pwr-. Matters are made worse by the fact that the front power buttons connection is part of a cluster of connections, so accidentally connecting power to pins that control the reset button or hard drive light are easy mistakes to make.
To solve this issue, youll need the manual to confirm where the power button connector goes, and you [might] need a magnifying glass to properly align the connection with the pins. If you cant find your manual, your motherboards manufacturer should have a PDF version of it on the companys site. Just search for your motherboards model number.
UEFI/BIOS hardware incompatibility
The Unified Extensible Firmware Interface [UEFI] and Basic Input/Output System [BIOS] connect your PCs firmware to its operating system. They help remind your computer what it is and what its supposed to do when first turned on, and that includes spotting any hardware errors.
Motherboards ship from the factory with a BIOS or UEFI that can handle contemporary hardware, but theyre not guaranteed to work with any hardware that gets released after they ship. That means you can have a new processor that isnt compatible with the hardware youre using due to an issue with new developments since the motherboard was manufactured. You will likely have to update to a BIOS or UEFI for it to function.
If this happens, your computer might refuse to boot your operating system after POSTing, or it might not POST at all. Fortunately, there is an easy solution to this issue. Youll take a step backward by re-installing the old hardware you had disabled to troubleshoot your problem. When you get your computer back to that status, reboot it. Once the old hardwares in, you can boot your computer, go to your motherboard manufacturers website, and find the latest BIOS/UEFI version. After installing the latest BIOS/UEFI version is complete, you can re-install your new hardware.
Conclusion
There are a few extra steps involved when youre trying to troubleshoot a motherboard compared to other tech issues, but its a crucial skill to learn if you plan to build and repair your PC. The experience you gain by replacing your motherboard gives you the potential to use the same computer for a decade [or more] by replacing the internals when necessary. Rest assured that the issues weve mentioned above are common occurrences with foolhardy solutions that may test your patience but will ultimately work. That said, if you feel like youre in over your head, you can always consult an expert, whether that means bringing your computer to a certified technician or calling the manufacturer.